Above Sölden, a 6.5 megawatt upright solar array built to shed its own snow is nearing completion, and panels already ran a ski lift through winter
At roughly 9,300 feet above Sölden, a steel column rises out of the snowpack like a leafless tree.
Four wings of dark glass branch out from its spine, standing straight up instead of tilting to the sky.
Wind moves around them and nothing white collects on the glass.
Long term data across a full decade of winters, not just one pilot season, will settle whether the shading tradeoff is a minor cost or a real ceiling on performance.
That is not an accident of the weather.
It is the entire reason the structure was built this way.
Here is how a panel that refuses snow actually works.
Why does standing the panels upright stop the snow from piling up
Conventional solar panels tilt toward the sky at a shallow angle, which is perfect for catching sunlight and equally perfect for catching drifting snow. Once a few inches settle on the glass, the whole panel goes dark until someone clears it by hand or the sun does the job days later.
The cross shaped support solves that by turning the geometry on its head. Because the four wings stand vertical and meet at a central column, they behave less like a roof and more like a fence post in open country.
The design team found that even at low wind speeds, the structure generates air turbulence that stops snow from settling, keeping the photovoltaic system clear of buildup. So instead of a dead array under a foot of white, the glass stays active through the exact months when an Alpine resort needs power most.
And the snow that does fall nearby does something else entirely.
A crater of snow that reflects light back into the panels
Picture the ground around the base of one of these towers after a storm. Rather than burying the structure, a scour ring forms around the base, which actually helps winter energy production. That crater is not wasted geometry, it becomes a mirror.
Sunlight bouncing off bright snow at high altitude is far stronger than the reflection off grass or gravel, a phenomenon known as the albedo effect. The cross shaped configuration reduces snow buildup around it, while the natural crater reflects light up toward the underside of the panels.
Because the panels use bifacial cells, meaning both faces generate power, the underside of each wing can capture that reflected light while the front face still takes direct sun. None of that would matter if the structure could not survive an actual winter at altitude, which is exactly what the project set out to prove.
The test system that ran a ski lift through one full season
Before committing to the full installation, the developer piloted a system with 12 bifacial tree shaped structures at 9,350 feet in Sölden, underneath the Tiefenbach glacier in Austria’s Ötztal Valley. The photovoltaic system powered a ski lift for an entire season, cutting reliance on grid electricity.
That result is what turned a prototype into a procurement decision. The full scale project that followed sits in a different category. Developers describe an installation in Sölden at an altitude between 9,350 and 9,850 feet with a capacity of approximately 6.3 megawatts, scheduled for completion in the second half of 2026, that will supply clean energy to three major ski resorts in the region.
The operator’s own resort pages, however, now describe the system as expanding to 6.5 megawatts peak by autumn, covering around 35 percent of the electricity needs of the local lift company. As of this autumn’s season opening, the resort was still describing the array as planned rather than finished, with that 35 percent figure framed as an eventual target.
Where the complication still lives, even in a design built for snow
Standing a panel on its edge solves the accumulation problem but creates a new one: shading. A tree like structure with four wings branching off one column inevitably throws shadow onto its own neighboring faces at certain sun angles, cutting output exactly when the array should be working hardest.
The system’s developer says shading variations and differences in rear side power gain do not drag down overall output, making the design particularly suited to bifacial panels in mountain terrain where snow reflection varies across modules. The project uses power optimizer technology that lets shaded sections keep producing independently instead of dragging down an entire string.
That tradeoff is worth watching as more of these towers go up elsewhere in the Alps, since upright arrays above the snowline are becoming a small but growing category across Austria and Switzerland. Long term data across a full decade of winters, not just one pilot season, will settle whether the shading tradeoff is a minor cost or a real ceiling on performance.
What ski resorts gain from power standing on its own feet
For an operator running snow cannons at two in the morning and chairlifts at dawn, the appeal is not abstract decarbonization, it is a bill. Electricity demand at altitude spikes hardest in the cold months, precisely when flat ground mounted solar in the valley below is weakest under its own snow load.
A structure that keeps working through the exact season a resort needs it closes that gap directly. The approach also travels well beyond Sölden. Any site with reliable snow cover, high winter demand and limited flat ground, which describes most of the Alpine ski industry, is a plausible next customer.
Similar reasoning has already pushed solar hardware into spaces built for something else entirely, from vineyard rows to parking structures. Whether the cross shaped tower becomes a common fixture on alpine ridgelines or stays a niche solution for a handful of resorts will depend on data still being collected one winter at a time, under the same snow it was built to shed.
Hugo is an engineer with strong technical expertise. Multilingual from an early age, his writing combines technical clarity with a strong interest in science and energy.
